Titebond

TITEBOND BLACKTOP REPAIR SEALANT

Titebond Blacktop Repair Sealant is a non-reactive, durable, acrylic latex formula specifically designed for repairing and sealing cracks in all asphalt surfaces. It dries quickly with a textured black color that blends well with surrounding surfaces. It will not peel, chip, crack or pull away from repaired areas due to temperature changes, UV light or severe weather changes. It helps prevent damage due to water and ice.

Features & Benefits

  • IDEAL FOR: Sealing driveways, playgrounds, parking lots and pavement.
  • SEALS: Asphalt, metal, masonry, wood and most common building materials.
  • Fills and seals cracks in asphalt surfaces
  • Weather-resistant seal
  • Durable and flexible - Resists oil, gas, grease & salt
  • Textured formula blends with surface
  • Extrudes easily, excellent adhesion
  • Mildew resistant
  • UV-resistant

Specifications

Exceeds:
  • ASTM C834 TYPE OP GRADE -18°C

Application Guidelines

  • Application Temperature: Above 40°F (4°C)
  • Service Temperature Range: -25°F to 180°F (-31°C to 82°C)
  • Method of Application: Cartridge/caulking gun
  • Working Time: Approximately 10-15 minutes for a 1/4" bead
  • Application Directions: 1. Surfaces must be clean and free of any material that may prevent adequate adhesion. Properly designed joint not to exceed 1/2" in width. 2. Cut tip at 45° angle to desired bead width and place in cartridge gun. 3. Force sealant into clean joint. If necessary, smooth bead immediately. 4. Do not allow foot or vehicular traffic on repaired area until it is completely dry. It is the sole responsibility of the user to thoroughly test any proposed use with all substrates to determine project suitability. NOTE: Two layers of Blacktop Repair, 1/4” to 1/2” thick that are allowed to dry thoroughly between applications, are better than one heavy layer.
  • Cleanup: Clean uncured material with water. After curing, excess sealant must be cut or scraped away.
  • Coverage:
    Container 1/8” Bead 1/4" Bead 3/8" Bead 1/2" Bead
    10.1 oz. Cartridge 123 ft. 31 ft. 14 ft. 8 ft.

Physical Properties

  • Type: Acrylic latex
  • Calculated VOC: <50 g/L (<1.5%)
  • Color: Black
  • Solids: 83%
  • Flashpoint: Solvent free/Not applicable
  • Viscosity: 550,000 cps
  • Freeze / Thaw Stability: Stable
  • Storage Life: 24 months in a dry location at or below 75°F

Limitations

Not designed for continuous submersion or use below the waterline. Air, sealant and surface temperature should be above 40°F. Do not apply if rain is expected within 12 hours. Cure time is dependent upon ambient conditions including temperature and humidity. The sealant should be dry to the touch and ready to paint in 2-4 hours. Allow to cure for 24 hours before direct contact with water. Wait 24 hours prior to coating with an asphalt or tar based driveway sealer. For best results, store in a dry location at or below 75°F.

Product SKUs

Part NumberUPCCase UPCSizeWeightUnits Per PackagePackages Per PalletColor
318103708303181210037083031819Currently Unavailable - 10.1 Oz. Cartridge15.4212108

Warranty Statement

Liability is limited to product replacement only.
Important Notice: Our recommendations, if any, for the use of this product are based on tests believed to be reliable. Since the use of this product is beyond the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or effects incidental to such use, handling or possession or the results to be obtained, whether in accordance with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore. Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict with existing laws and/or patents covering any material or use.
2020 Bruck Street, Columbus, Ohio 43207
CUSTOMER SERVICE 1-800-669-4583
TECH SERVICE 1-800-347-4583
www.titebond.com

Franklin International