TITEBOND URETHANE REPAIR SYSTEM


The Titebond® Urethane Repair System is a two-part urethane system that enables contractors to repair loose or popping areas in a finished floor. The adhesive in the system is of low viscosity that sets quickly and is fully cured within 45 minutes of application. The easy flow characteristics of the urethane adhesive,...

more

Features & Benefits

check_circle
Repairs popping and hollow spots
check_circle
No visible defects from repair
check_circle
Easy flow adhesive
check_circle
Simple assembly process
check_circle
Highly moisture resistant
check_circle
Will not cause dimensional changes in wood flooring
check_circle
Strong ultimate bond
check_circle
Unaffected by freezing temperatures
check_circle
Contains no water
check_circle
Low viscosity
check_circle
Flows easily
check_circle
Extremely small hole to drill (1/8" drill bit) for the 1/16" needle on gun
check_circle
Will not become brittle
check_circle
Easy assembly process
check_circle
Quick curing process
check_circle
Reusable gun

Application Guidelines

Assembly of Titebond Repair System:
  1. With the black handle facing forward, insert the black plastic 4:1 ratio plunger into cartridge gun with the flat side going in first.Note: Press upwards on the silver button on rear of gun to allow plunger to slide smoothly backwards. Pull back until plunger is fully retracted.
  2. Place 50 ml cartridge into gun making sure to close down the plastic locking mechanism.
  3. To remove 50 ml cartridge cap, turn cap 1/4 turn counterclockwise and then pry off. Be sure to hold cartridge upright when removing cap.
  4. Remove cap from 50 ml cartridge and twist the clear plastic mixing nozzle onto the cartridge.
  5. Place slip-on needle on to mixing nozzle.
Preparation of Repair Area:
  1. Locate center of popping or loose area to be repaired.
  2. Find a dark grain in the wood flooring piece, to aid in hiding repair.
  3. Once the area to repair has been located, place a 2" strip of blue tape where the hole will be drilled. This will mark the spot and aid in the cleanup process.
  4. Use 1/8" drill bit and drill a hole through the tape and wood flooring. Drilling on an angle will prevent backflow of adhesive.
To Repair Hole:
  1. Insert needle into the 1/8" diameter hole and squeeze the gun handle to begin filling popping area.
  2. Continue to squeeze adhesive into the hole until void is filled.
  3. Remove the strip of blue tape and wipe away any excess amount of adhesive on the wood with water and a soft cloth or sponge.
  4. After filling process is finished, insert toothpick into the hole.
  5. After 5-10 minutes, break the toothpick off flush with the floor.
  6. Use either colored putty or a crayon to fill excess gap around the toothpick.
Cleanup:
Wet adhesive can be cleaned up with water and a soft cloth or sponge. If adhesive has dried, use mineral spirits and a soft cloth. For best results, place a 2" strip of blue tape where the hole will be drilled. Once the repair process is complete, remove the strip of tape with any backflow of adhesive on it and clean remaining amounts with water and a soft cloth or sponge.
Limitations:
Do not leave adhesive stationary in mixing nozzle for more than 10 minutes, as adhesive will cure in nozzle. Prepare all injection sites before using adhesive for best results.

Physical Properties

Type
Two-part urethane
Flashpoint (Multithane R2032)
Not applicable
State (Multithane R2032):
Liquid
Flashpoint (Hardener 200)
> 200°F.
State (Hardener 200)
Liquid
VOC (Multithane R2032)
Not applicable
Color (Multithane R2032)
Beige
VOC (Hardener 200)
Not applicable
Color (Hardener 200)
Dark brown
Freeze/thaw Stability
Stable
Storage Life
2 years

Specifications Guide

TOOLS NEEDED: INCLUDED WITH REPAIR KIT: OTHER ITEMS NEEDED:
  • DRILL
  • 1/8" DRILL BIT
  • BLUE TAPE
  • GUN
  • NEEDLE
  • STATIC MIXING BOZZLE
  • TOOTHPICK
  • COLOR PUTTY STICK OR CRAYON

Caution Statement

WARNING: EYE AND SKIN IRRITANT. POTENTIAL SKIN AND RESPIRATORY SENSITIZER. Contains isocyanate containing polymers. Contact causes eye irritation. Prolonged or repeated skin exposure may cause irritation and sensitization or allergic reaction. Harmful if inhaled. May cause allergic reaction. Toxic fumes released in fire situations. Do not allow eye contact. Avoid prolonged or repeated contact with skin. Avoid breathing vapors. For additional information, refer to Safety Data Sheet. KEEP OUT OF THE REACH OF CHILDREN.

Warranty Statement

Important Notice: Our recommendations, if any, for the use of this product are based on tests believed to be reliable. Since the use of this product is beyond the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or effects incidental to such use, handling or possession or the results to be obtained, whether in accordance with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore. Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict with existing laws and/or patents covering any material or use.